We were asked to supply and install a new high-performance wall-mounted pressure washer system for a dairy farmer in Atherstone. The customer needed a more powerful and reliable solution for cleaning down the dairy after each herd visit, as his existing equipment was struggling to keep up with daily demands.

Problem / Requirement

• Existing machine: The farmer was using an unreliable Kränzle pressure washer that frequently failed and wasn’t suitable for heavy, regular dairy cleaning.
• Main issues: Lack of power, poor reliability, and increased downtime during daily washdowns.
• Site conditions: Cleaning takes place after each cow visit, requiring regular, efficient washdowns in a demanding environment.
• Usage: Daily use for dairy cleaning and hygiene maintenance.

The customer needed a stronger, more durable system that could deliver consistent performance and reduce interruptions to the milking routine.

Our Solution / Work Carried Out

• Supplied and installed a SystemWash AquaJet 3 stainless steel three-phase cold wall-mounted pressure washer for maximum durability and power.
• Mounted the unit securely to the wall to keep it off the floor and protect it from dirt, water, and equipment movement in the dairy.
• Raised the machine to a safe height so the cows could not reach or damage the unit during milking or movement in the dairy.
• Fitted protective edging around the outside of the frame to prevent the cows from catching or injuring themselves on any sharp corners.
• Installed a chemical injector to allow for low-pressure chemical application during washdowns, helping break down dirt and improve hygiene.
• Set up the system to provide a reliable high-pressure feed to make dairy washdowns quicker and easier after each milking session.
• Installed the system in a fixed position to provide a clean, organised, and permanent washdown point.
• Commissioned the machine on-site and ensured the customer was fully trained and confident in operating the system.

The Result

• The new AquaJet 3 system delivers significantly more power and performance compared to the previous Kränzle unit.
• Cleaning the dairy after each herd visit is now quicker, easier, and more efficient.
• The chemical injector allows effective low-pressure detergent application, improving cleaning results and hygiene.
• Raising the machine prevents cows from reaching or damaging the equipment, improving reliability and reducing the risk of downtime.
• Protective edging ensures there are no exposed sharp edges, helping maintain a safe environment for livestock and staff.
• The wall-mounted design keeps the equipment protected, tidy, and out of the working area.
• The customer now has a reliable, high-duty cleaning system suitable for daily agricultural use, reducing downtime and improving hygiene.

We were asked to supply and install a new high-performance pressure washer system for a logistics company in Ellistown. The customer relies heavily on pressure washing for pallet cleaning and wanted more power along with a reliable backup solution as part of their move to a larger site.

Problem / Requirement

• Existing machine: The company already had a DTE pressure washer from their previous site.
• Main issues: The existing DTE unit didn’t provide enough power for the increased workload at the new facility.
• Site conditions: A dedicated wash booth was already built, and the customer needed a clean, organised setup without hoses trailing across forklift routes.
• Usage: Frequent daily pallet washing as part of ongoing logistics operations.

The customer needed a more powerful primary machine, with the original DTE retained as a backup to prevent downtime and production delays

Our Solution / Work Carried Out

• Supplied and installed a Nilfisk SC Uno to provide a higher-powered primary washdown system.
• Reallocated the existing DTE pressure washer as a dedicated backup unit to ensure continuity in the event of a breakdown or service requirement.
• Ran high-pressure pipework around the rear of the wash booth to feed the washing area cleanly and safely.
• Connected the system to a wash boom, preventing hoses from lying on the floor or being driven over by forklifts.
• Constructed UniStrut frames and mounted both machines securely to the building structure so they were level, organised, and off the ground.
• Positioned the machines for easy access, making servicing, maintenance, and operation straightforward.

The Result

• The Nilfisk SC Uno provides increased power and performance, improving pallet washing efficiency.
• The original DTE unit now serves as a reliable backup, reducing the risk of downtime and supporting continuous operation.
• The wash boom and rear pipework eliminate hoses on the floor, preventing damage from forklifts and creating a safer, tidier workspace.
• The UniStrut mounting keeps both machines secure, level, and easy to work on, improving long-term maintenance and usability.

We were asked to design and build a fully mobile pressure washer system for a driveway cleaning contractor based in Birmingham. Having worked with this customer previously, his business had expanded following a new contract, and his cleaning requirements had changed significantly.

He supplied two diesel pressure washers and asked us to fabricate a secure, van-mountable system that would allow him to operate independently of mains water and electricity.

Problem / Requirement

• Existing setup: Two diesel pressure washers mounted on trolley frames.
• Main issue: Machines were not optimised for van installation and off-grid operation.
• Operational challenge: Required a fully self-contained system for working in areas with no water or power supply.
• Business growth: Increased workload meant efficiency, reliability, and professional setup were now essential.

The contractor needed a secure, compact, and practical solution that could be mounted inside his van and used anywhere.

Our Solution

• Removed both diesel pressure washers from their original trolley frames.
• Fabricated and installed a custom mounting frame suitable for secure van installation.
• Mounted both machines directly to the frame to create a stable, integrated system.
• Connected the machines to the van’s main water tank for fully independent operation.
• Installed anti-vibration mounts to reduce stress and movement on the frame during transport and operation.
• Fitted two hose reels to keep hoses organised, protected, and easy to deploy.
• Ensured the system could be mounted and removed efficiently when required

The Result

• The contractor now has a fully self-contained, off-grid pressure washing system.
• Both diesel machines are securely mounted and integrated into the van.
• Anti-vibration mounting improves durability and reduces long-term wear.
• Dual hose reels keep the setup neat, professional, and quick to use.
• The system allows him to work anywhere, even where no water or electricity is available.
• His upgraded setup supports his new contract requirements and business growth.

We were asked to resolve an exhaust issue for a company in Lichfield using a Nilfisk Truck Booster hot pressure washer to clean their lorries. The machine is installed inside a container unit and is used regularly for fleet washing.

Originally, the boiler exhaust was vented directly out of the rear of the container, which was sufficient at first. However, as site operations changed, lorries began parking behind the container — causing exhaust smoke to blow directly onto trailers during hot water use.

 Problem / Requirement

• Existing setup: Nilfisk Truck Booster located inside a container, flued directly out of the rear wall.
• Main issue: When using hot water, boiler exhaust smoke was venting onto parked lorry trailers.
• Operational change: Lorries were now being parked directly behind the container.
• Risk: Smoke residue on clean trailers and poor exhaust management.

The system itself was working correctly, but the flue arrangement no longer suited the updated site layout

Our Solution

• Supplied and installed a new external stainless steel flue system.
• Redirected boiler exhaust vertically above roof height to disperse safely into open air.
• Removed the previous rear-facing exhaust outlet configuration.
• Secured and sealed the flue system to ensure safe, compliant operation during hot water use.
• Tested the system under load to confirm proper exhaust draw and performance.

The Result

• Boiler exhaust is now safely vented above roof level.
• No smoke is discharged onto parked trailers.
• Hot water cleaning can be used without affecting surrounding vehicles.
• The container installation remains compact and efficient while complying with safe exhaust practice.
• The customer can continue washing their lorry fleet without operational disruption.

A paint removal company in Tamworth made the decision to consolidate several operating sites into one central facility. As part of the move, all pressure washing operations needed to be relocated and integrated into the new premises.

The customer operated three pressure washer systems in total — two high-flow pump and motor units, along with a Nilfisk SH Truck Booster that had been in service for around 15 years. Before any of the machines could be installed, the new site required a complete inlet water and high-pressure pipework network to support the wash bay operation.

Problem / Requirement

• Multiple pressure washing systems previously spread across different sites.
• New premises required a complete inlet water and high-pressure distribution network. 
• Wash bay needed reliable access to both water supply and high-pressure cleaning points.
• Pipework route was complex, involving multiple bends, elevations, and stacked pipe runs.
• Existing machines required collection, refurbishment, repair, and relocation before installation.
• Customer wanted provision for future expansion and additional operators.

The challenge was creating a pipework system capable of supporting daily industrial use while allowing multiple machines to operate efficiently from a single location.

Our Solution

• Designed and installed a complete inlet water supply system for the pressure washing equipment.
• Installed twin high-pressure pipework runs feeding the wash bay area.
• Routed and stacked pipework through multiple sections of the building to suit site constraints.
• Collected all three pressure washers from their original locations.
• Reconditioned and repaired each machine before relocation.
• Installed two primary pressure washer systems for daily operation.
• Installed the third machine as a standby unit, ready for future expansion or additional operators.
• Tested and commissioned the complete system to ensure reliable operation across all wash points.
• Relocated and integrated the existing 15-year-old Nilfisk SH Truck Booster into the new setup.

The Result

• One centralised pressure washing facility replacing multiple separate site installations.
• Reliable inlet water and high-pressure infrastructure built for daily industrial use.
• Improved workflow and efficiency by bringing all cleaning operations under one roof.
• Refurbished equipment given a new lease of life rather than requiring full replacement.
• Backup pressure washer available immediately if demand increases or maintenance is required.
• Future-proofed installation capable of supporting additional operators and business growth.

This was one of those installations where the pipework itself was every bit as challenging as the machinery. Careful planning and routing allowed us to deliver a clean, practical solution that tied together equipment from multiple sites into one efficient pressure washing system.

We were asked to install a new electric three-phase cold static Electrajet wall-mounted pressure washer system for a manufacturing company in Nottingham. The customer had recently expanded into a new warehouse and needed a powerful, reliable cleaning solution to support component washing and day-to-day operations.

Problem / Requirement

• Existing setup: The customer had no fixed pressure washer system in the new warehouse and relied on portable equipment in other areas of the site.
• Main issues: Limited cleaning efficiency, no hot water assistance, and increased workload due to expanding production.
• Site conditions: A dedicated washroom was in place, requiring pipework and remote operation to keep the area clean and organised.
• Usage: Regular weekly use for cleaning manufactured components and general washdown tasks.

The customer wanted a permanent, professional installation that would deliver higher cleaning performance, reduce manual effort, and prepare the new warehouse for increased demand.

Our Solution / Work Carried Out

• Installed a three-phase electric cold static wall-mounted pressure washer for high-power cleaning in the new warehouse.
• Fitted a thermal mixing valve on the inlet plumbing to provide a stable, continuous supply of warm water and improve cleaning performance.
• Ran pipework into the washroom to supply the cleaning point neatly and efficiently.
• Installed a remote start/stop control to allow the machine to be operated from inside the washroom without accessing the main unit.
• Fitted a compact hose reel to keep the wash area tidy and make handling the hose easier during cleaning.
• Mounted the system securely to the wall to keep it off the floor and maximise workspace.

The Result

• The new three-phase wall-mounted system provides powerful, reliable cleaning for components and general washdown tasks.
• The thermal mixing valve delivers a controlled warm water supply, helping debris and contaminants remove more easily compared to cold water alone.
• Pipework, remote controls and the hose reel keep the washroom organised, tidy and easy to operate.
• The customer now has a permanent, efficient cleaning setup that supports their warehouse expansion and makes cleaning tasks quicker and less labour-intensive.

We were asked to install a new static hot Nilfisk SH Truck stainless steel pressure washer system for a farm in Twycross that sells and maintains ATV bikes. The customer needed a reliable hot water machine for regular equipment cleaning but struggled with low water pressure and wanted the unit kept indoors with simple external operation.

Problem / Requirement

• Existing machine: An older Ehrle HSC unit was already on site and required frequent repairs.
• Main issues: Low mains water pressure, inefficient workflow, and the need to operate outdoors without accessing the plant room.
• Site conditions: All cleaning is carried out outside, and the system needed to avoid freezing and dirt exposure.
• Usage: Approximately 10 hours per week for ATV and farm equipment cleaning.

We had been repairing the Ehrle machine for the customer for years, but ongoing repair costs and performance limitations made a new installation the best long-term solution.

Our Solution / Work Carried Out

• Supplied and installed a Nilfisk SH Truck static hot stainless pressure washer as the primary washdown system.
• Installed a 200L water barrel to guarantee a consistent feed despite low mains pressure.
• Fitted a boost pump between the barrel and machine to deliver a smooth, steady flow to the high-pressure pump.
• Installed a chimney flue through the wall to safely vent boiler exhaust outside.
• Drilled through the wall and fitted an external hose point and retractable hose system for outdoor cleaning without moving the machine.
• Installed external remote start/stop controls so the operator can run the machine from outside the building.
• Repaired and retained the existing Ehrle HSC as a backup machine for the farm.

The Result

• The Nilfisk SH Truck now provides reliable hot water cleaning, making ATV washdowns quicker and more efficient.
• The 200L tank and boost pump ensure smooth, consistent pressure even with low mains supply.
• External controls and hose access allow operators to wash equipment outdoors without entering the building, saving time, reducing freezing risks, and keeping the plant room clean and secure.
• The customer has reduced ongoing repair costs while still keeping the old machine as a backup.

We were asked to design and install a completely custom pressure washer system for a professional vehicle detailer in Coalville. The customer wanted a compact, wall-mounted setup that would fit neatly into the corner of his workshop, provide spotless rinsing for finished vehicles, and make daily washing quicker and easier.

Problem / Requirement

• Existing setup: The detailer was using a cheap portable pressure washer from the side of his mobile van and did not have a dedicated setup in his workshop.
• Main issues: No access to ionised or purified water, water spotting and streaks on final rinses, limited pressure and performance, and slow workflow due to constantly moving equipment.
• Site conditions: Limited workshop space, corner installation required, and daily washdowns on detailed vehicles.
• Usage: Regular weekly use for professional valeting and detailing work.

The customer wanted a permanent, professional system that was fixed in place, out of the way, and designed to improve finish quality and workflow inside the workshop.

Our Solution / Work Carried Out

• Built and installed a fully custom wall-mounted pressure washer system designed to fit perfectly into the corner of the workshop.
• Fitted a TDS (Total Dissolved Solids) meter to enable the use of ionised water for spot-free, streak-free final rinses.
• Integrated ionised water capability to improve finish quality on detailed vehicles.
• Installed a 20-metre hose reel beneath the pump hardware with lightweight hose to make vehicle washing easier and reduce drag across the floor.
• Added a nozzle holder on the side of the machine to allow quick changes of spray angle for different cleaning tasks.
• Mounted the system securely to the wall to keep the unit off the floor, maximise workspace, and protect the equipment.

The Result

• The custom wall-mounted system delivers compact, efficient operation while freeing up valuable floor space in the workshop.
• The TDS meter and ionised water capability allow for spot-free, streak-free rinsing, improving the finish on detailed vehicles.
• The 20-metre lightweight hose and reel make washing easier, faster, and more ergonomic during daily use.
• The nozzle holder enables quick spray-angle changes, making the cleaning process more versatile and convenient.
• The customer now has a clean, professional setup that’s permanently fixed, out of the way, and tailored specifically to his workflow.

We were asked to design and install a new site-wide washdown system for an industrial site in Burton. The customer wanted multiple wash points positioned around the facility to make cleaning quicker, easier, and more efficient, without having to move equipment from place to place.

Problem / Requirement

• Existing setup: The site previously relied on a single pressure washer and portable hose trolleys.
• Main issues: Time-consuming setup, constant equipment movement, trailing hoses, and limited cleaning performance.
• Site conditions: Large, busy outdoor and indoor areas requiring regular washdowns to keep the site clean and presentable.
• Usage: Frequent daily washdowns for general site cleaning and maintenance.

The customer needed a fixed, professional washdown system that provided instant access to water across multiple locations without dragging hoses or relocating equipment.

Our Solution / Work Carried Out

• Installed multiple wall-mounted wash points across the site, fed by the central Delta booster system.
• Set up low-pressure wash points for high-volume rinsing and general cleaning tasks.
• Installed high-pressure wash points for heavy-duty cleaning where stronger performance was required.
• Fitted stainless steel hose reels at every location for durability and corrosion resistance.
• Installed automatic retractable warm-water reels at the high-pressure points for easy handling and improved cleaning performance.
• Installed hand-wind stainless reels at the low-pressure points for simple, reliable access to volume water.
• Designed the system so operators can simply pull a hose, press the trigger, and wash, with no need to move equipment around the site.
• Connected all wash points back to the central Delta booster to ensure consistent water supply and pressure.

The Result

• The site now has instant access to washdown facilities at multiple locations, improving workflow and efficiency.
• High-pressure points provide powerful cleaning for heavy-duty tasks, while low-pressure points deliver high-volume rinsing where needed.
• Stainless steel reels and components ensure long service life in demanding industrial conditions.
• Automatic retractable reels keep wash areas tidy, eliminate hose clutter, and improve safety.

We were asked to supply and install a reliable cold static pressure washer system for an emergency services site in Leicester. The machine is used for regular ambulance washing, helping keep the fleet clean and presentable.

Problem / Requirement

• Existing setup: The site required a dedicated, fixed pressure washer for vehicle cleaning.
• Main issues: No permanent washdown system in place and a need for fast, efficient cleaning to minimise vehicle downtime.
• Site conditions: Ambulances require frequent cleaning, with quick turnaround times and minimal setup.
• Usage: Regular daily washing of emergency service vehicles.

The customer needed a dependable, easy-to-use system that would allow staff to wash vehicles quickly without moving having to move equipment or fight tangled hoses.

Our Solution / Work Carried Out

• Supplied and installed a Nilfisk DTE cold static pressure washer as a fixed vehicle washdown solution.
• Built and installed a custom stainless steel mounting frame to securely house the machine and protect it in a busy working environment.
• Installed an automatic retractable hose reel beneath the unit to keep the wash area tidy and make hose handling quick and effortless.
• Modified the system to ensure smooth hose operation and easy access during vehicle washing.
• Mounted the system at an ergonomic height to allow fast connection and efficient use when washing ambulances.
• Fully commissioned the machine and ensured the system was ready for immediate use.

The Result

• The Nilfisk DTE system now provides a reliable, fixed washdown solution for ambulance cleaning.
• Ambulances can be washed quickly and efficiently, reducing downtime and improving fleet presentation.
• The automatic retractable reel keeps the area clear of trailing hoses, improving safety and organisation.
• The custom stainless steel frame provides durability, protection, and a clean professional finish.
• Staff can now simply pull the hose, wash the vehicle, and retract the reel—making daily cleaning faster and easier.

We were asked to supply, install, and fully customise a Nilfisk 400HS DTE pressure washer system for a FedEx site, used for cleaning lorries on a daily basis. The customer needed a reliable, user-proof setup that could handle multiple operators while preventing misuse, damage, and unnecessary downtime.

Problem / Requirement

• Existing setup: Standard machine configuration not suited to a busy lorry washdown environment.
• Main issues: Risk of unauthorised use, inconsistent water supply, and potential fuel-related burner issues.
• Site conditions: High-traffic depot with multiple users and frequent, heavy-duty cleaning of vehicles.
• Usage: Daily lorry washdown requiring consistent performance, reliability, and ease of use. 

The system needed to be robust, simple to operate, and protected against the common causes of failure in high-use environments.

Our Solution

• Supplied and installed a Nilfisk 400HS DTE pressure washer system.
• Fitted keypad access (PIN or fob) – ensures only authorised users can operate the machine, reducing misuse, preventing accidental damage, and improving accountability.
• Modified the flue system – prevents rainwater entering the boiler, reducing corrosion, avoiding burner lockouts, and extending boiler life.
• Installed a Tiger Loop system – removes air from the fuel line and stabilises fuel delivery, resulting in a cleaner burn, fewer flame failures, and more reliable operation.
• Upgraded fuel system with new tank and low fuel cut-out – automatically shuts the machine down if fuel runs low, preventing dry running, sooting, and costly burner damage.
• Installed low water cut-out – protects the pump by shutting the system down if water supply drops, eliminating the risk of running dry and damaging internal components.
• Set up low-pressure and high-pressure chemical systems – gives flexibility for different cleaning stages, from pre-soaking and foaming to deeper, more aggressive cleaning when needed.
• Added a pressure accumulator – smooths out pressure spikes, improving user experience while reducing stress and wear on the pump.
• Installed rear-mounted hose reel – keeps hoses organised and off the ground, reducing trip hazards, preventing damage, and improving overall site tidiness.
• Fitted a boost pump – ensures consistent inlet pressure regardless of site supply fluctuations, improving performance and significantly increasing the lifespan of the main pump.

The Result

• A fully customised lorry wash down system built specifically for a busy FedEx depot.
• Controlled access reduces misuse and extends the life of the machine.
• Improved burner reliability with a stable, clean fuel system.
• Full protection against low water and low fuel conditions, preventing breakdowns.
• Smoother, more consistent performance for all users.
• Safer, cleaner working environment with better hose management.
• A long-term solution designed to minimise maintenance, reduce downtime, and maximise reliability.

Modifications carried out on a Nilfisk SH Truck for a haulage company in Shepshed to improve reliability and resolve ongoing fuel and water supply issues.

The machine is used regularly for cleaning HGVs and trailers, so a consistent, self-contained setup was required to minimise downtime and improve day-to-day operation.

Problem / Requirement

• Machine drawing fuel from a bunded IBC tank located behind the workshop
• Ongoing fuel supply issues causing inconsistent burner performance
• Air entering the fuel line leading to flame failures and lockouts
• No fuel level protection, with risk of running the tank dry
• Inconsistent water supply creating risk of inlet starvation
• Requirement for a more reliable, simplified setup suitable for regular use

Our Solution

• Installed inlet water tank to provide a constant buffer of water to the machine stopping inlet starvation and cavitation. The tank ensures consistent flow to the pump, improving reliability and pump lifespan
• Installed new dedicated fuel tank, removing original reliance on external IBC fuel supply, eliminating issues caused by long fuel lines and inconsistent fuel draw. Reduces risk of air ingress and contamination and improves burner performance and combustion stability
• Installed fuel level switch (low fuel cut-out) that automatically shuts the machine down when fuel level is too low; prevents the burner running dry

The Result

A significantly more reliable and user-friendly setup tailored to the demands of a busy haulage environment.

The system now benefits from a consistent water supply, a stable and controlled fuel source, and built-in protection against common failure points.

This upgrade removes previous fuel-related issues and protects the machine from avoidable damage, ensuring it can operate reliably under regular daily use.

We were asked to design and build a dedicated wheel wash system for a hatchery in Rugby. The system needed to be installed externally and provide a reliable, controlled cleaning process to maintain strict site hygiene standards for incoming vehicles.

Problem / Requirement

• Existing setup: No dedicated wheel wash system in place for controlled vehicle entry.
• Main issues: Risk of contamination entering the site, inconsistent cleaning methods, and no structured wash process.
• Site conditions: Outdoor installation exposed to the elements, requiring a robust and weather-resistant solution.
• Usage: Frequent vehicle access requiring a consistent and repeatable cleaning process using multiple detergents.

The customer required a fully self-contained system capable of delivering a structured multi-stage wash process, while being durable enough for outdoor use.

Our Solution

• Supplied and installed a DTE stainless steel cabinet suitable for outdoor use.
• Built the system around a CAT pump for reliability and consistent performance.
• Installed a Kothar triple outlet turn and clean system to allow a 3-stage detergent application process.
• Configured the system to handle multiple detergents for a structured wash procedure.
• Integrated an internal hose reel for a clean and organised working setup.
• Fitted an internal water inlet tank to ensure consistent water supply and protect the pump.
• Designed the system as a fully self-contained unit for ease of use and minimal operator error.

The Result 

• A fully bespoke wheel wash system tailored to strict hygiene requirements.
• Consistent and repeatable 3-stage cleaning process for all incoming vehicles.
• Reliable performance thanks to high-quality components and controlled water supply.
• Durable, weather-resistant setup designed specifically for outdoor installation.
• Cleaner, more organised system layout with improved usability for operators.
• Reduced risk of contamination entering the site through proper wash procedures.

This installation delivered a purpose-built solution that goes beyond a standard pressure washer, providing a controlled and reliable cleaning process suited to the demands of a biosecure environment.

We were asked to replace an ageing Nilfisk Neptune 7 setup for a fleet cleaning company in Tamworth. The customer wanted to repurpose their existing mobile machine into a van setup, meaning a new static system was required to handle the daily cleaning workload reliably.

Problem / Requirement

• Existing setup: Older Nilfisk Neptune 7 machine previously used as the site’s main cleaning system.
• Main issues: Boiler scaling issues, ageing components, and the need to free up the mobile machine for van use.
• Site conditions: High-use fleet cleaning environment requiring reliable hot water performance and consistent chemical application.
• Usage: Regular vehicle and fleet washing with varying cleaning requirements depending on contamination levels.

The customer required a more permanent and reliable static installation that would improve long-term reliability while also giving greater flexibility with chemical application and system protection.

Our Solution

• Supplied and installed a brand new Nilfisk SH Truck static pressure washer system.
• Removed and replaced the old Neptune 7 installation.
• Installed a new stainless flue system for safe boiler exhaust management.
• Fitted low-level cut-outs for water, chemical, and fuel to protect the machine from running dry.
• Installed both low-pressure and high-pressure chemical injection systems for improved cleaning flexibility.
• Fitted a water softener system to reduce scale build-up and protect the boiler and internal components.
• Modified the inlet water tank and installed a new float valve system for improved water regulation and reliability.
• Reconfigured the site setup to allow the original Neptune 7 to be repurposed into a mobile van cleaning unit.

The Result

• A modern static hot wash system built specifically for daily fleet cleaning use.
• Improved system protection through integrated low-level safety cut-outs
• Reduced risk of boiler scaling and improved long-term reliability thanks to the water softener installation.
• Greater flexibility in cleaning performance with both high and low-pressure chemical application.
• More reliable water control through the upgraded tank and float valve setup.
• Allowed the customer to continue using their Neptune 7 as a separate mobile cleaning solution without compromising the site setup.

This installation not only upgraded the customer’s main cleaning system, but also improved the overall efficiency and flexibility of their operation moving forward.